Last Updated on June 19, 2022
If you’ve recently purchased a new swimming pool liner, you’ve probably wondered why it doesn’t touch the wall. This problem can be caused by the liner not stretching enough to cover the entire pool’s surface. You need to make sure that the overlap is the same all around the pool so the floor seam stays in one place.
If you don’t have a tape measure, you can use a piece of coping to make sure that the liner is properly overlapping the wall.
Fixing wrinkles in a pool liner
Trying to remove wrinkles from your swimming pool liner can be difficult. Although a professional cleaner will most likely be able to help you, a few tips can be helpful in getting your liner back in top shape. If you want to avoid hiring a professional, here are a few tips that you can follow.
Firstly, drain the water from your swimming pool. While it may be tempting to use a vacuum cleaner to remove wrinkles, this method will actually damage your liner.
If your liner is starting to form wrinkles, make sure to repair the rip as soon as possible. If you notice any wrinkles on the wall of your pool, it’s likely due to a leak. Water gets behind and underneath the liner, forcing it upward.
You can either patch the rip or repair the leak by adjusting the ground around your pool. However, be sure to keep the water out of the pool while patching.
Using a toilet plunger to remove wrinkles in your pool liner is another way to fix your problem. The plunger’s gripping power can help you pull out stubborn wrinkles without draining the pool. You should also use hot water to soften the liner.
To avoid bleaching your pool liner, add some pre-solving or fast-dissolving shock to the water. If you have a large wrinkle, try using an unused toilet plunger to pull it upward.
A high-pH level and high chlorine are harmful to vinyl and cause it to pucker and contract. If you are having trouble getting the liner to fit properly, you may want to take it to a professional cleaner. However, if the problem persists, it may be best to get a new liner. The average life expectancy of a vinyl liner is seven to ten years.
The next step in fixing wrinkles in a pool liner is finding the source of the leak. Small leaks in the liner may allow water to enter the pool and force it up. If you have a leak, you need to locate it as quickly as possible. Otherwise, you may have to drain the water and patch it.
If you have a leak in your liner, you must repair it immediately or risk having a damaged liner.
A high-pH level or low-chlorine level are common causes of wrinkles on a vinyl liner. To fix the problem, you can drain the water from the pool. Unfortunately, this is not the best option because you may damage the liner structurally.
You may also have to pay to have it replaced altogether. If you can’t afford this, the best option is to get it repaired at a professional.
Working out coving in a pool liner
You can start by measuring and marking the overlap on your pool liner. The overlap will keep the floor seam at the same place. Measure the length and width of the pool liner, making sure to overlap evenly around the entire pool. You can use a piece of coping to help stabilize the pool wall.
You can also use spring clamps to temporarily clip the liner to the wall. Once you’ve mapped out the coving, you can begin installing the new pool liner.
Work out the perimeter using a pencil or a ruler. Use the uprights to guide yourself while lining the pool. The wall-to-floor seam should be approximately midway down the coving around the edge. Place clothes pegs at the three or four locations around the perimeter.
This will keep the liner from rotating. You can use cardboard to hold it in place. Make sure the liner is evenly tensioned throughout the perimeter.
If you find wrinkles along the sides of your pool liner, they’re most likely caused by improper installation. The liner may have been made too small and stretched into the cove.
This is fine, as it is completely normal. When the cove is too small, the liner will be too tight in the cove and create an ugly appearance. This is a common problem with above-ground pools with overlap liners.
You can also use a tape measure to determine how much extra material you need to fill in the cove. Generally, you don’t need more material than you need, but you should still have enough.
You can always cut a little extra lining in some places and work it out later if you need to. After you’ve finished your pool liner, secure the liner by using coping strips around the perimeter wall.
Before installing your liner, make sure you drain your pool completely. This will prevent the liner from shrinking. Then, remove the top rails to open it. You should use two people to help you remove the liner. One person should hold the liner while the other holds it, smoothing it out, and adding sand if necessary.
After the coving has been completed, you can check the area around the cove with a tape measure and note whether it is separating.
When installing your new liner, it is important to make sure you have enough slack material to fit the coving. After you’ve measured it, you can work out the excess material and smooth it out.
Remember to check the bottom edge and floor of the liner for wrinkles. While you’re doing this, make sure to use the vacuum to remove any air trapped behind the liner.
Hanging a pool liner on rounded ends
To hang a pool liner on rounded ends, you must begin at the center of the pool and work outwards. You can use the seams on the liner as a guide. Once you reach the ends of the pool, you can use coping strips to hold the liner in place.
You can also use alligator clips to ensure the liner will stay attached to the wall. To prevent unclipping, have someone hold the section where you started.
The liner should be about three to seven inches bigger than the pool, with a gap of approximately 3 to 7 inches around the cove. If it is too tight, you will have to pull a bit more liner out of the pool and overlap it over the wall.
Also, don’t add water too fast or the liner will not hang flat. Make sure you measure the cove and hang the liner accordingly.
You can also measure the length and width of the pool to determine the correct size of the liner. To find out the right length, measure a quarter of the way around the pool.
Measure the length and width of the wall, but remember to round up the measurements for standard liner sizes. To make sure that the liner is not touching the wall, you should measure the walls twice.
Once you have measured the length of the pool, you can decide if the above-ground liner is right for your space. The overlap liner is the least expensive above-ground pool liner, as it drapes over the wall of the pool. However, if your pool has a deep end, you should purchase an overlap liner.
However, be sure to read the manufacturer’s installation instructions carefully.
You can also choose a beaded liner, which is the easiest to install. Beaded liners usually have a bead on the top edge, and the liner is tucked into this track. You can purchase conversion kits to convert from overlap to bead setup.
You can also buy a J-hook liner, which has a thick rubber fold along the top edge. These liners do not require coping strips and can be installed over the top rails.
In addition to avoiding damage to the walls, make sure you install your liner correctly. An incorrect installation can lead to a blowout and costly repairs. Even if you purchase a new liner, you can’t guarantee its quality. You’ll have to pay for the replacement if it doesn’t hold.
For this reason, it is always better to hire a professional to install your liner for you.
You must also make sure you hang a pool liner on rounded ends so that it does not touch the wall. This is essential because sharp objects can puncture the liner and cause a leak. Always remember to keep the wall away from the liner during installation.
There are also some tips that you should keep in mind when installing a pool liner. When using the vacuum, use the water slowly. Filling the pool too quickly can cause damage to your liner.
Frequently Asked Questions (FAQs)
My pool liner isn’t touching the wall, what do I do?
There are two possible scenarios here. The first is that your liner is too big for the pool and needs to be trimmed down. The second is that the liner is not properly positioned on the pool wall.
In either case, you will need to adjust the liner so that it fits snugly against the pool wall. If the liner is too big, you can use a sharp knife to trim it down to size. Be sure to leave enough excess material so that you can reposition the liner if needed.
If the liner is not positioned properly, you will need to drain the pool and remove the liner. Once the liner is removed, you can reposition it on the pool wall and fill the pool back up.
What kind of adhesive should I use to attach my pool liner to the wall?
There are a variety of adhesives that can be used to attach a pool liner to the wall. Some examples include silicone sealant, contact cement, and double-sided tape.
When choosing an adhesive, be sure to select one that is specifically designed for use with pool liners. This will ensure that the adhesive will bond properly and provide a long-lasting hold.
How often should I replace my pool liner?
Pool liners typically need to be replaced every 5-7 years. However, this can vary depending on the type of liner and the amount of use it gets. If you notice any holes, cracks, or other damage to your liner, it is important to have it repaired or replaced as soon as possible to avoid further damage.
Last Thoughts
There could be a few reasons why your pool liner is not touching the wall. It could be that the liner is too small, the wall is not level, or there could be something blocking the liner from touching the wall. If you are unsure of the reason, it is best to consult a professional to help you troubleshoot the problem.
