What to Do If Cordless Drill Gets Wet?

Last Updated on July 15, 2022

The best way to dry a cordless drill after it gets wet is to wipe off any excess water. Trying to engage a wet power tool can damage the tool or short out.

Wiping off the inside and the outside of the tool will prevent further damage. This article also explains the importance of adjusting settings and MG Chemicals Acrylic Aerosol Conformal Coating. To dry your tool completely, follow these steps:

MG Chemicals Acrylic Aerosol Conformal Coating

It is important to protect your cordless drill from moisture when working in wet conditions. To prevent water from damaging the electronics in your drill, you can use MG Chemicals Acrylic Aerosol Conformal Coating.

The product is a clear, one-part varnish coating that is very thin and adheres to various substrates. The coating is extremely durable and resists corrosion and moisture.

Heat treatment

Heat treatment

Cordless drills need proper care during and after usage. They’re more susceptible to damage and battery drain when exposed to extreme heat and direct sunlight. Additionally, moisture can damage the battery and wiring.

To avoid damage to your drill, you should keep it away from these two conditions. To help ensure the maximum life of your drill, you should follow these tips to protect it. Keep reading to learn how to protect your cordless drill from wet or hot conditions.

First, make sure to replace the battery in the drill. The battery is easily replaced by simply opening the drill side and inserting a new one. To protect the internal electronics, apply a layer of conformal coating.

Silicone or lacquer-based coatings are best. Ideally, 2 to 3 coats are recommended. Another layer of coating protects electrical contacts. Another layer of coating protects the batteries.

Cleaning with distilled water

If you’re going to use a cordless drill outdoors, make sure you keep it well-ventilated. Then, whenever the tool gets wet, clean it with distilled water.

It will prevent any spots and streaks from forming and will also remove any mineral deposits that may have gotten on it. Whether your drill gets wet from a shower, a puddle, or a small spill, distilled water will keep it in good condition.

Adjusting tool settings

If your cordless drill gets wet, make sure to adjust the tool’s settings. These settings are connected to torque, which is the rotational equivalent of force. Think of it like twisting a faucet handle.

The higher the torque, the faster the drill will run down the battery. If the tool runs down too quickly, it may experience the “memory effect” that results in the tool not working properly.

You can also adjust the clutch on your drill by looking for an arrow next to the number. If it’s too loose, you can turn the ring to increase the torque. If you’re drilling into brick, for example, you’ll want to use a masonry bit.

The torque setting controls the amount of force the tool applies when driving screws. For soft materials, use the low torque setting, while for timber, you can use a high torque setting. Lastly, you can adjust the forward/reverse switch to change the direction of the chuck.

To adjust the settings on your power tool if it’s been wet, you’ll need to open it up. Remember that a power tool contains electronics and other parts that are most susceptible to water damage.

Therefore, you’ll need to take your time in disassembling the tool. Taking a picture of all the components and their locations is helpful, too. Make sure you take note of all the parts in your drill before disassembling it.

Frequently Asked Questions (FAQs)

-Is it still safe to use the drill if it gets wet?


It is not safe to use the drill if it gets wet.

-How can you dry out a wet cordless drill?

If your cordless drill is wet, you can dry it out by using a hairdryer. Set the hairdryer to the lowest setting and hold it about six inches away from the drill. Move the hairdryer around the drill so that all the wet areas are dried. Once the drill is dry, you can use it as normal.

-What are some tips for preventing a cordless drill from getting wet?

Some tips for preventing a cordless drill from getting wet are to avoid using it in areas where there is a lot of moisture, to keep it in a case when it is not in use, and to make sure the batteries are dry before putting them in the drill.

Verdict

If your cordless drill gets wet, unplug it immediately and remove the battery. Allow the drill to dry completely before using it again.

About the author

Leave a Comment