Last Updated on August 19, 2022
There are several ways to store your circular saw, and this article covers some of the most important steps for proper storage. In addition, you should remember to follow safety precautions while using your saw, such as keeping the blade sharp and avoiding kickback.
Read on to learn how to put your circular saw back into its protective case after each use. Whether you’re working on a small project, or on a large one, safety precautions are important.
Safety precautions
There are a number of safety precautions to be followed when putting circular saws back in their cases. For starters, you should always use personal protective equipment when using circular saws, such as eye protection.
The blade of your saw should be sharp and the abrasive wheels should be free of defects. You should also unplug your circular saw when not in use and store it in a safe place away from children.
Another important safety precaution is to always keep the blade offset set at a level of one eighth to one quarter inch below the work piece. Make sure the power is off before making these adjustments, and place the work piece on a bench or two sturdy sawhorses.
Remember to prop up the material as needed, as it can fall off and buckle the blade, leading to dangerous kickback. Always turn the saw off when not in use and make sure it is unplugged.
Lastly, remember that your circular saw does not automatically cut square. You will need to mark the cut location with a framing square.
Then, place the framing square on top of the workpiece and draw a dark, straight line at the mark. Be careful when cutting reclaimed wood, as it can contain screws or nails. Leaving these behind can cause damage to the wood or even injury.
Another important safety precaution when putting circular saw back in case is to always make sure the blade guard is retractable.
Most blade guards have a spring-back mechanism that retracts automatically after a cut. Using a circular saw when it is plugged in can be dangerous, and is one of the biggest safety risks. Therefore, you must use caution when you use it, and be sure to read all safety instructions on the case before using it.
Properly align the wood for cutting before you put it back in the case. If the piece is sagging or warped, make sure the blade is level.
You should also ensure the blade is sharp before cutting it. When putting your circular saw back in the case, it’s a good idea to check the blade for cracks and chips, and make sure it’s sharp enough to cut through it easily.
Setting up a circular saw
Before you use your circular saw for the first time, there are some things you need to know. Ensure that the blade is set to 90 degrees, or ideally just slightly less.
You can check the position of your blade by using a framing square or speed square. If it’s too far off, loosen the bevel adjustment screws. If the blade is not positioned correctly, it can kick back and cause damage. Cross-cutting is relatively simple, and it’s completely safe if you know what you’re doing.
Before using your circular saw, you should always wear appropriate eye protection and tough work gloves. The blade can get caught in your eye and permanently blind you. Losing an eye is irreversible, so safety glasses will not give you the proper protection.
Safety goggles are the best choice for complete protection. It’s also a good idea to keep your saw unplugged when you’re not using it. If you don’t use your circular saw for a long time, you’ll likely damage the blade and have to replace it.
If you’ve used your circular saw, you’ll want to put it back in its case as soon as possible. Be sure to unplug it from the wall outlet. Remember to remove the blade guard from the circular saw as well.
You’ll want to keep your hands away from the saw blade to avoid accidents. When making adjustments, remove your finger from the trigger and keep it away from small children. You’ll be glad you did.
Set the blade to 1/4-inch below the material you’re cutting. You can also back the blade slightly. When you’re ready to use your circular saw, you need to engage the trigger.
The blade should retract into the case once it reaches its full depth. Once you’ve cut the lumber, the blade should stop and the guidesaw should close automatically. If it doesn’t retract, you can adjust the guidesaw manually to cut angled pieces.
After you’re finished with your cut, it’s time to place the circular saw back in its case. You may also want to adjust the depth of your cut. Most circular saws feature adjustable pivots so you can cut beveled edges.
To adjust this angle, turn the adjustment knob counterclockwise until it’s tight. In most cases, this allows you to adjust the angle of your cut. You can also adjust the depth of the cut by adjusting the depth and the bevel.
Keeping a blade sharp
One of the best ways to avoid injury when using a circular saw is to keep the blade sharp. The blades of these power tools can become dull after a period of time, and if you don’t sharpen them properly, your work can be slowed down, your finish could be uneven, and you could suffer kickbacks.
Circular saw blades are usually carbide-tipped, but there are also masonry blades that use a different type of blade. The carbide blades use the entire blade to cut, whereas masonry blades cut only the surface. Keeping the blade sharp is crucial when using a circular saw, because a carbide blade will saw almost anything.
Before putting a circular saw back into the case, you should sharpen the blade. To do this, you will need oil, a sharpening stick, and a small piece of wood about five inches long and three inches wide.
First, remove the blade from the saw and fix it in a bench vice or clamp. Then, mark the first tooth on the blade. Repeat the process for all other teeth.
Changing the blade is one of the easiest ways to improve the quality of your cuts. You can also clean the blade before sharpening it, which will make it much easier to sharpen.
If the blade is a dirty one, you can use a soft toothbrush or soap to clean the entire blade. This will give you a clear idea of what is wrong. You can also try a file to get rid of the highest teeth.
A common mistake in putting a circular saw back in the case is not removing the blade. Simply lift up the base plate and gently press the saw down.
If you can’t do this, you can use a set of lockable pliers or Vice-grips to remove the blade while loosening the bolt. Just be sure to use a wrench that fits the blade properly. If not, you’ll risk damaging the bolt.
Preventing kickback
Circular saws with anti-kickback devices can be an essential tool for homeowners. These tools prevent kickback while using the saw by preventing it from moving backwards or forwards during operation.
The device has two parts: a retaining plate and a spring. The spring pushes against the saw’s back case while the anti-kickback device pinches the roller against the footplate.
The first thing you must do to prevent a kickback while using a circular saw is to tighten the wood on both ends. If you do not, the board will bend and bind on the saw’s blade, resulting in a circular saw kickback.
You can support the edges of the board with a 2×4 or other suitable support. In the absence of supports, the board will bend and will bind on the blade.
Another important tip when using a circular saw is to use a sharp blade. A dull blade will not cut as well as a sharp blade, and it will be more likely to kick back.
Furthermore, a dull blade will not cut the workpiece as smoothly as a sharp blade and will bind in the wood. In order to prevent kickbacks, you must follow all safety precautions and instructions given by your manufacturer.
Another tip to prevent kickbacks when using a circular saw is to make sure the back case is secured properly. This will prevent a kickback by preventing the blade from coming out of the wood.
It’s essential to follow all guidelines for circular saw safety, as these precautions will help you keep your work piece from flying off your table. So, what are you waiting for? Get started today by following these guidelines and prevent kickbacks from happening.
Frequently Asked Questions (FAQs)
-How do you properly store a circular saw?
When not in use, store your circular saw on a shelf or in a cabinet. If you must store it on the floor, place it on a level surface to prevent it from tipping over. Be sure to keep the cord away from any heat sources, and keep the blade covered to protect it from damage.
-What is the best way to keep a circular saw blade sharp?
The best way to keep a circular saw blade sharp is to use a saw blade sharpener.
-How do you change the blade on a circular saw?
To change the blade on a circular saw, first unplug the saw. Then, remove the blade guard and the old blade. To install the new blade, put the blade on the arbor, making sure that the teeth are pointing in the correct direction. Then, tighten the arbor nut to secure the blade in place. Finally, replace the blade guard and plug in the saw.
-How do you make sure a circular saw is level?
To make sure a circular saw is level, you need to check the blade guard to see if it is level with the table. If it is not, you need to adjust the blade guard until it is level with the table.
-What are some safety tips to follow when using a circular saw?
Some safety tips to follow when using a circular saw include:
-Wearing proper eye and ear protection
-Keeping the saw blade sharp
-Using a guide or fence when cutting
-Cutting with the grain whenever possible
-Supporting the workpiece properly
-Holding the saw firmly with both hands
-Avoiding kickback by not forcing the saw and using the proper blade for the material being cut
Conclusion
If you need to put your circular saw back in its case, first make sure that the blade is properly secured. Next, locate the case’s foam insert and lay it out on a flat surface. Place the saw on the foam insert, making sure that the blade is facing up. Finally, place the lid on the case and secure it with the latches.
