Can You Plaster Over Lining Paper?

When you’re plastering, you might wonder whether you can plaster over lining paper. This depends on the type of wall you’re plastering. You might choose Woodchip, Artex, or Dry plaster.

Or you might opt for a mix of both. The key is to test a small area first to see what results you can expect. Then, apply a coat of plaster over the glue. If everything goes well, you can proceed to the full room.

Artex walls

Plastering a room using artex plaster can be a challenging task. However, with a few basic steps, the plaster can be removed. First, the artex needs to be thoroughly cleaned. After that, apply a layer of plaster over it.

Allow this layer to dry for 15-30 minutes before applying another layer. If there is still visible artex texture, a third coat of plaster may be required.

Taking care to avoid damage to the artex surface is crucial. Plastering over it is harder than plaster board or previously plastered surfaces. You should first skim over the artex surface with a stiff wire brush, then apply a wallpaper stripper or vinegar and fabric softener solution in a spray bottle.

To remove the remaining layers of artex plaster, you will need a 3-in-one scraper tool.

After the plaster has dried, you can apply a layer of lining paper. If the artex surface is made of asbestos, scrape it off carefully with a scraper or knife. It is essential to remember that this process can cause injury if you are in close proximity to the asbestos-filled surface.

Therefore, artex plastering over lining paper should only be done by an experienced plasterer. There are other methods, like using a roller, but they need expertise and plenty of time.

If you are painting a room with Artex, you can use a lining paper to protect the surface from damage. Plastering over lining paper is not recommended, as it may cause the plaster to come down or crack. In addition, it may make the plaster hollow and crack. In this case, you should hire a decorator.

The price of the work depends on the size of the room. There are also a few considerations to consider, such as the size of the ceiling.

Once you have decided on the type of plaster you want, it’s time to determine whether you should go for a DIY project or hire a professional to remove the Artex.

This method is not always the easiest, but it does make sure that all the asbestos is gone from the room. However, it is the most expensive. In addition, it is not always possible to remove the Artex plaster over lining paper without hiring a professional.

Woodchip

When you are considering a new look for your interior, the first thing you should consider is whether woodchip plaster is right for your project. Woodchip is typically painted, but you can use it without paint if you prefer a more rustic look.

This type of plaster is also very durable, with a strength rating of Better Than 90%. While woodchip is difficult to apply, it does require some effort. Here are some tips to make the process easier:

First, soak the woodchip wallpaper in hot water. Add a little washing up liquid, if you can, to slow down the runoff of the woodchip to the floor. You can also use DIF Wallpaper remover, as it dissolves the paste more easily.

For best results, you should also remove the old wallpaper before starting the project. This way, you won’t have to worry about getting dust all over the place or worrying about damaging the wall.

If you can’t get rid of the lining paper, you can still try plastering over it. However, it isn’t recommended by decorators because plaster needs to adhere to a tacky surface. To hide the woodchip, you can also use a woodchip bark covering.

Similarly, if the wall is already painted, you can hide the woodchip by applying a coat of primer. This will help protect the plaster and avoid any problems during the plastering process.

If you are planning to add woodchip plaster over the lining paper, be sure to follow the manufacturer’s instructions for the removal of the paper. If the paper isn’t ripped or damaged, you might end up goinguge the wall a bit.

You may also need to clean the surface thoroughly, but this will be a relatively straightforward process if you’ve already cleaned the walls. If you have multiple coats of paint, you may want to do two or more passes.

When using woodchip plaster over lining paper, you should make sure the lining paper is completely flat and even. This will give the wall a flat and even surface for painting or wallpapering.

If the lining paper is textured, you should scrape the paper off first. If there are any areas of the paper that are damaged, you may need to apply a third coat. When using a third coat of plaster, you should make sure that you have smooth surfaces for the new plaster.

Wood

Plastering over wood is tricky. Professional plasterers rarely plaster over wood. Some people do it, though, albeit with less success. Wood is too porous to bond well to the plaster, and applying it directly to the surface could result in a disconnect.

If you are plastering over a wooden panel, use an all-purpose joint compound instead. If it’s glossy, de-gloss the surface first, and then apply the plaster.

The next step in plastering is to prepare the wall. You can apply the PVA emulsion to the surface, but you need to clean it first. It will prevent the plaster from sticking to the wall and will protect it from any debris that may come in contact with it. It can be applied in one coat or two.

Make sure the walls are clean and free of any loose particles or scuff marks, as this will prevent the plaster from adhering properly.

Afterwards, clean the artex surface with soapy water. If the plaster doesn’t stick, you may need to apply a layer of primer before you start applying the plaster. Do not remove the layer of artex if you do not want the plaster to stick.

The dust from artex contains low levels of asbestos. If you breathe in the dust, it can harm your lungs and cause complications.

Once you have prepared the walls, you should measure the width of the wall and cut the lining paper to match. It is important that the lining paper is well attached to the wall because it provides the plaster with good “bite” – otherwise, the plaster will pull the paper off the wall and leave you with an uneven surface.

Then, apply the lining paper. Follow the steps above for a smooth, seamless finish.

Dry plaster

Plastering over lining paper can be an excellent way to cover an unplastered wall without having to replace it. This method is not only quick and easy, but also requires you to move furniture and place plastic sheeting over the baseboard.

To prevent plaster from leaking onto the floor, you can also tape plastic sheeting to the baseboard. However, plastering can be messy, so make sure to take proper precautions.

Before plastering, you need to prepare the wall surface. This is crucial to achieving a high-quality finish for the paint or wallpaper. It is not always easy to find out what’s behind the latest floral vinyl or recent latex.

To avoid this issue, you need to make sure you’ve removed any previous wallpaper or lining paper and then use a suitable plaster. This process takes about three hours and requires a minimum of three coats of paint.

It is possible to skim plaster over lining paper, but you shouldn’t do so. It will likely crack and fall off. Skim tends to stick to rough surfaces better than smooth surfaces.

But wallpapers are often coated with a layer of vinyl, making it less likely to stick to the wall. To avoid this problem, paint the walls free from dust and cooking oils. The plastering process will proceed more smoothly if the lining paper is removed.

If you don’t want to risk wallpapering paste sticking to the walls, you can try applying sizing solution. This solution creates a slightly glossy surface so that the paper paste will stick to the wall. Drying plaster can also suck moisture out of the paste, making it dry too quickly.

The lining paper can be replaced with the new wallpaper once the plastering is complete. However, if you can’t afford to remove the wallpaper, it is always better to go for lining paper than to replaster the wall.

When plastering old walls, it is best to apply multiple layers of PVA primer. PVA is essential for the adhesion between the new plaster and the lining paper. You can then sand the area with fine sandpaper. Make sure not to oversand because this could damage the surrounding wall.

You can then apply another coat of PVA on top of the sanded area. The final step is to let the plaster dry for a week before you decorate.

Frequently Asked Questions (FAQs)

1. Will the plaster adhere to the lining paper?

The plaster will adhere to the lining paper if the surface is clean, dry, and free of any debris or contaminants. If the surface is not properly prepared, the plaster may not adhere correctly and could cause problems with the finished product.

2. How well will the plaster smooth out over the textured surface of the lining paper?

The plaster will not smooth out over the textured surface of the lining paper.

3. Is it necessary to remove the lining paper before plastering, or can it be left in place?

It is not necessary to remove the lining paper before plastering, but it can be left in place.

4. How thick should the layer of plaster be in order to adequately cover the lining paper?

The thickness of the plaster should be about 3/16 of an inch.

5. Are there any potential problems with plastering over lining paper that should be considered before beginning the project?

The main potential problem with plastering over lining paper is that the plaster may not adhere well to the paper. This could cause the plaster to crack or peel off of the paper, which would ruin the finish of the project.

It is important to test a small area before proceeding with the entire project to ensure that the plaster will stick to the lining paper.

Verdict

Based on the information gathered, it appears that you can plaster over lining paper. However, it is recommended that you consult with a professional before doing so to ensure that the results are what you expect.